Quad Eachine EX110

D.O.G.

Goblin 380 Supporter
what are your throttle endpoints? and also go into cleanflight with just the USB cable connected (no battery) and make sure motor stop is turned on.

Here's my end points 100/-129 and I did go into cleanflight with just the usb and the motor stop was off. I turn it on, save/reboot.
 

D.O.G.

Goblin 380 Supporter
On your endpoints, try 100/-140 and see what that does.

:hmmm: My lowest endpoint is -129. I'm not sure what's else to do. Your probably running out of Ideas your self :buttkick:. I might have no other choice but to buy another one and keep this one as a spare unless someone,somewhere might know something about this tricky situation that I got my self into. Thanks Tony :wave:
 

D.O.G.

Goblin 380 Supporter
Update on the Ex110. Well HeliDirect made good by me. With no question asked, they gave me store credit on the return of the EX110. Jody the quad specialist mention that Echine been having problems with there FC especially on the 110.
I did some window shopping and was wondering what you all think. I'm going to get a QX90c since I have parts and pieces for it. I was looking at 2 quads that I might get. #1 TBS X-RACER (DSMX/DSM2) - Racing Platform - FPV Racing or #2 RJX 95mm Brush FPV Racing Quadcopter Drone Kit (Unassembled) - Tinywhoop Frame - Tinywhoop or just get that QX90c and call it good enough for me.
 

duncaj07

New Member
I have an EX110 DSM which worked fine. Now whenever I connect the battery, the props turn fast like max rpm. How can I reset everything and just start over?
 

Tony

Staff member
Have you connected it to the computer and made sure motor stop was turned on and verified you have the correct channel sequence?
 

duncaj07

New Member
This is a DSM version. so I have UART3 set to serial RX in the port page and RX serial selected on the receiver page. I also selected spectrum for the channel mapping.
 

Tony

Staff member
You may be experiencing the same issues I did then which caused me to basically toss the FC into the trash. The FC on this quad is complete crap. Might be time to look into another brushless FC. That is what I would have had to do if I wanted to get it back in the air. Might contact who you purchased it from and see if they can cut you a deal on one.
 

gwen3134

New Member
hello i have an eachine ex110 drone but i can't bind my irange dsmX receiver with my radio can someone help me?
 

D.O.G.

Goblin 380 Supporter
Hey there gwen and :welcome1:to the forum. In order to help you can you provide a little bit more information? Like what TX your using or and if the RX blinking or not?
 

gwen3134

New Member
Salut gwen et: welcome1: sur le forum. Afin de vous aider, pouvez-vous fournir un peu plus d'informations? Aimez-vous ce TX que vous utilisez ou et si le RX clignote ou.


Hi then the blue led stays fixed and there is the red led flashing. - Dimensions: 92x92mm - Weight: 43g - F3 Flight Controller v1.2 - DSM receiver - 8520 Brush motor - Propeller size: 55mm - Camera: EF-01 800TVL HD CMOS 1/3 " - Video format: PAL / NTSC - 5.8Ghz 25mW 40CH video transmitter - 1S 3.7V 600mAh Lipo battery Micro price - Battery strap - USB charger - Flight time: about 6 minutes on the other hand there is no button for bind on the card.
 
Last edited:

D.O.G.

Goblin 380 Supporter
Well gwen, I'm useless to you since I'm clueless on the jumper TX. Question here; doesn't that TX has a way to bind the RX with the TX using the TX it self like spectrum TX can? Check the manual...if you can.
 

RandyDSok

Well-Known Member
I'm pretty sure the Jumper T10 does have a DSMX mode... so make certain it's set to that before you try to bind. Beyond that, I can't help much either ...
 
Top Bottom